Repointing Starts With What Goes Back In The Joint
Repointing means cutting out worn mortar and replacing it. The cutting is labor. The part that decides whether the wall holds up is the mortar we put back. A mix harder than the brick will outlast the brick, and on an old Chicago wall that shows up as spalled brick faces a few winters later. We read the brick and the old mortar first, then pick a mix built to wear out before the brick does.
The Joint Is Supposed To Lose
A brick wall is never still. It swells a little when it gets wet, shrinks when it dries, grows on a hot August afternoon and pulls back on a January night. Something in that wall has to absorb the movement. You want it to be the mortar, because a joint can be cut out and replaced. A cracked or spalled brick face is permanent.
Water follows the same logic. Every masonry wall in Chicago gets soaked, whether it is snow piled against the foundation all February or a gutter that dumps onto the same corner every storm. That water has to leave the wall somehow. A softer, more porous mortar gives it an exit. Close that exit with a dense, hard joint and the water goes out through the brick instead, and when it freezes in the brick face, the face pops off. That is why masons call the joint sacrificial. It is designed to be the weak part.
Lime, And Why Old Walls Were Built On It
Most Chicago bungalows, two-flats and courtyard buildings put up before about 1930 were laid in lime-rich mortar. It is soft and it breathes. Small cracks in lime mortar can even close on their own over time as the lime takes in carbon dioxide from the air and hardens again. The common brick those walls were built from is soft too, fired from local clay, and it can vary in hardness from one brick to the next in the same course.
That pairing has worked for a hundred years on a lot of buildings. The trouble starts when somebody repoints it with a modern cement-heavy mix because it sets fast and feels strong.
Type O, Type N, Type S: What The Letters Mean
Modern masonry mortar is graded by letter. More portland cement makes it harder and slower to pass water. More lime makes it softer and lets the wall breathe. The ones that matter on a house wall:
- Lime mortar, lime and sand with little or no portland cement. The softest and most breathable option, and usually the right one for soft pre-1930s common brick.
- Type O, a low-strength mix heavy on lime. A good fit for many older walls above grade that are not carrying heavy loads or sitting in constant wet.
- Type N, the general-purpose middle. Right for a lot of above-grade walls of harder, denser brick, like postwar face brick and raised ranches.
- Type S, higher strength. Used below grade, on retaining walls and on some hard caps. Too hard for soft brick, and the wrong reach on most old Chicago walls.
The premixed bag a handyman grabs off the shelf is usually one of the stronger types. On a 1950s face brick ranch that may be fine. On a 1920s two-flat it can do real damage.
If the new mortar outlasts the brick around it, the mix was wrong.
Matching Hardness To The Brick In Front Of Us
We test before we choose. Old lime mortar scratches easily with a key and turns to powder. A previous hard repair rings when you tap it and barely marks. Then we look at the brick itself: soft common brick has a sandy, open face and rounded corners, while face brick is dense and sharp-edged.
Plenty of Chicago houses carry both. The bungalow on your block probably has a hard face brick front and soft common brick down the gangway side and across the back. Same building, two different answers, and we will tell you when one wall gets a different mix than another. If an earlier crew already repointed with hard gray mortar, the chipped and spalled brick right beside those joints is usually the proof.
Sand Carries The Color
Most of a mortar joint’s color comes from the sand. Old Chicago mortar was often made with local sand, coarser than what goes into a modern bag, and a century of weather has worn the surface so those grains show. A smooth gray modern mix next to it reads as a patch from across the street.
So we match sand color and grain size first, then the binder, then a small amount of pigment only if it needs it. We break off a piece of old mortar to see its true color under the weathered surface, mix small samples and let them dry fully before comparing, because wet mortar looks much darker than it will on the wall.
Where A Roofing Crew Fits In
We came to masonry from the roof. Every counter-flashing we install above a roofline is set into a cut mortar joint, and that joint gets repointed when the metal goes in. Parapet copings and chimney shoulders are masonry that sits right in our work area. The same mortar rules apply up there, with more weather.
A Straight Answer Before We Cut
Before work starts you hear which mix we plan to use, why, and how the new joints will look next to the old ones, including how long they take to settle in color.
Mortar We Mix
Lime mortar for soft pre-1930s brick. Type O or Type N for most house walls above grade. Type S only where the brick and the exposure call for it.
Sand and color matched to your old joints and checked dry before anything goes on the wall. Browse the gallery for the roof work behind this crew.
(312) 590-4853How We Pick A Mix
Scratch The Old Joint
A key or a pick tells us right away whether we are looking at original lime mortar or a hard cement repair from a later decade.
Read The Brick
Soft common brick or dense face brick, sound or already spalling. The weakest brick on the wall sets the ceiling for the mortar.
Dry A Sample
Small batches with different sand and binder, cured and dried, then held against a freshly broken piece of the original joint.
Confirm Before Cutting
You see the sample and hear the reasoning. Nothing gets cut out of the wall until the mix is settled.
Choosing the mortar is half of it. How the joint gets cut, packed and tooled is covered in our brick repointing walkthrough. Soft historic brick and lime work get extra care under tuckpointing restoration, and if you are not sure the joints need repointing yet, start with reading mortar joint failure. Stone trim and block walls need their own mixes, which is what masonry tuckpointing is about. Parapet copings tie straight into flat roof repair. We repoint across Chicago, Oak Park and Berwyn.
Questions About Repointing Mortar
Is repointing the same thing as tuckpointing?
In everyday Chicago use, yes. Both mean cutting out failed mortar and packing in new. Tuckpointing originally named an older finish with a thin decorative line, but today most people use the two words for the same job.
Why not use the strongest mortar so it lasts longer?
Because the joint is supposed to be the part that gives. A mortar harder than the brick forces movement and water into the brick itself, and soft brick answers with cracked and spalled faces. A softer joint wears slowly and can be repointed again someday. A ruined brick has to be cut out.
Will the new mortar match the color of my old joints?
We match the sand first, since it carries most of the color, then the binder and a little pigment if needed. Samples are dried before we compare, because fresh mortar dries lighter. Expect the new joints to look a bit crisp for a few months while they weather in.
My house was repointed years ago with hard gray mortar. Can that be fixed?
Usually, but it is slower work. Cutting hard mortar out of soft brick risks chipping the brick edges, so more of it is done by hand. We tell you which areas are worth cutting out now and which are holding well enough to leave for later.
Can you repoint in the winter?
Mortar needs temperatures holding above about 40 F while it is placed and while it cures. In the cold months that means enclosing and heating the work area, or waiting for spring. Lime mixes are slower to set, so we are even more careful with them late in the year.
How can I tell if my brick is the soft kind?
Soft common brick usually has a sandy, open surface, rounded corners and a range of shades from one brick to the next. If the brick down your gangway looks different from the brick on the front, it probably is. We test it on the visit before choosing a mix.
Tell Us About The Brick
A close photo of a few joints and the brick around them, plus roughly when the building went up, tells us a lot about the right mix. Call or send it through the contact page and you will get a straight answer on what your wall needs.