Tuckpointing The Stone, Block And Trim Around Your Brick
Most talk about tuckpointing is about brick. Very few Chicago buildings are only brick. There are limestone sills under the windows, a concrete block back wall or garage, glass block in the basement openings, a stone foundation course on the older houses and a parapet along the roof. Each of those takes its own mortar and its own kind of cut, and a crew that treats them all like common brick leaves damage behind.
One Building, Several Kinds Of Joint
Walk around a typical south side bungalow or a two-flat in the near west suburbs and count the materials. The joint between two common bricks is one problem. The joint under a limestone sill, the joints in a cinder block garage and the wide joints in a rubble stone foundation are different problems with different answers. Here is what changes from one unit to the next:
- Concrete block is hard and hollow, so the cut is limited by how thick the block’s face shell is.
- Limestone is softer than most people assume and stains easily, so the mortar and the cleanup both change.
- Rubble and fieldstone have wide, irregular joints that need many lifts and a lot of hand work.
- Glass block absorbs no water at all, so the joints around it carry all the movement and all the runoff.
- Parapet walls get wet from both faces and the top, which makes them the hardest-working masonry on the building.
Limestone Sills And Lintels
Chicago builders trimmed a huge share of their brick houses in limestone: window sills, lintels over openings, coping stones and front step treads. A sill is a water shelf. Rain lands on it, runs to the front and drips off, and the joints at each end and along the bottom are where water gets into the wall below. When those joints open up, the brick under the window is usually the first brick on the house to spall.
Limestone wants a soft, lime-rich mortar, and it needs gentle cleaning, because a harsh wash can etch the stone and cement smears can leave stains that do not come out. If the sill stone itself is cracked through or has dropped, that is a stone repair and possibly a sign of movement, and we will say so instead of pointing around it.
Concrete Block Walls
Block shows up on garages, back additions, basement walls above grade and a lot of commercial buildings. The joints are usually a standard three eighths of an inch, but a block is hollow, with a face shell only so thick. Cut too deep and you are into the cavity. So the cut on block is controlled closely and the mix is usually a general-purpose mortar, since block is hard and does not need the soft lime treatment old brick does.
Painted block hides a lot. Paint holds water behind it and bridges over cracked joints until the paint itself peels. And a crack that runs up a block wall in a stair-step pattern, especially with blocks pushed out of line, is a structural question first. We do not tuckpoint over that until someone has looked at what is moving.
The mortar that suits the brick can be the wrong mortar for the stone sitting on top of it.
Stone Foundations And Rubble Walls
Older houses and outbuildings around Chicagoland sometimes sit on stone foundations, and some garden walls and older commercial buildings are laid in rubble stone. Those joints are wide and uneven, and many of them were laid in lime. They have to be raked by hand, packed in several lifts and shaped to the stone instead of struck in a neat line. On the part of the foundation above grade, white salts on the face are a sign that water is moving through the wall, and that water needs a way out. A hard cement repoint traps it.
The same goes for a poured or block foundation where it rises a foot or two above the yard. That band takes splash from every rainstorm, snow drifted against it until March and whatever the downspout drops at the corner. The joint where the foundation meets the first course of brick is a common place for mortar to wash out. Before we point it, we look at the grading and where the downspout empties, because a joint sitting in standing water will fail again no matter how well it is packed.
Glass Block Surrounds
Glass block windows went into a lot of Chicago basements to replace rotted sash. The weak point is the mortar around the panel and between the blocks, which takes every bit of expansion and every drop of water, because the glass takes none. No grinder goes near glass block. Joints there are raked out by hand and repointed carefully. If blocks are cracked or the panel has shifted in the opening, we tell you the panel needs replacing.
Parapet Walls, Where The Roof Comes In
Flat-roof buildings in Chicago, from storefronts to three-flats, end at a parapet. It is exposed on the street side, the roof side and the top, so it freezes and thaws harder than any other wall. The counter-flashing that protects the roof edge is set into a cut mortar joint on the roof side of that parapet. That is roofing work, and it is how we came to masonry in the first place. When we repair the roof edge, the coping joints and the parapet joints get handled by the same crew in the same visit.
Parapet tops matter most. A coping stone or tile cap with open joints lets water straight down into the core of the wall, where it shows up weeks later as a stain on a ceiling or loose brick on the inside face. Those joints get cut out and repointed, and the counter-flashing joint below them gets the same care, so the wall and the roof edge stop leaking into each other.
Send us photos of the whole wall, trim included, through our contact page.
Units We Point
Common and face brick, concrete block, limestone sills and lintels, stone foundation courses, glass block surrounds and parapet walls.
Stair-step cracks with displaced units get a structural look before any pointing. Flat roofs and parapet edges we have worked are in the gallery.
(312) 590-4853How We Handle A Mixed Wall
Map The Materials
We note every unit type on the elevation, brick, block, stone trim and glass, and where each one meets the next.
Mix Per Unit
A softer lime mix for limestone and old stone, a general-purpose mix for block, each matched in color to what is there now.
Hand Tools Near Trim
Grinders stay on long brick and block runs. Around sills, lintels and glass, the joints come out by hand.
Protect The Stone
Limestone is kept clean as we go, since mortar smears and harsh washes both mark it for good.
For the brick itself, start with brick tuckpointing on Chicago houses. Older stone and lime work that needs a careful match falls under tuckpointing restoration. Apartment buildings, storefronts and churches with mixed masonry are covered by commercial tuckpointing, and the whole envelope, sills and copings included, is the subject of exterior tuckpointing. Parapets on flat-roof buildings go hand in hand with flat roof repair. We take mixed-masonry calls in Naperville, Joliet and Tinley Park.
Questions About Block, Stone And Trim
Can you tuckpoint a concrete block garage?
Yes. Block joints are cut carefully because the face shell of a hollow block is thin, and the new mortar is matched to the hardness of the block. If the block is painted, we look at whether the paint is trapping water before we point.
My limestone sill has a crack across it. Is that tuckpointing?
The joints around the sill are, and they are usually what lets water into the wall below. A crack through the stone itself is a stone repair. If the sill has dropped or tilted back toward the house, we look at why before doing anything else.
Do you use the same mortar on stone as on brick?
Not always. Limestone and old rubble stone usually get a softer, lime-rich mix, while hard block takes a general-purpose mortar. On one wall we may mix two batches so each material gets a joint that is weaker than the unit beside it.
The mortar around my basement glass block is crumbling. Can that be fixed?
Usually. The joints are raked out by hand, never with a grinder, and repointed. If blocks are cracked or the whole panel has shifted in the opening, repointing will not hold it, and the panel needs replacing.
Why does the parapet on my flat roof keep needing work?
A parapet is wet on three sides and freezes harder than any other wall on the building. Coping joints and the counter-flashing joint on the roof side fail first. We handle the joints and the roof edge together, since our crew is already up there.
My block wall has a stair-step crack. Do you just tuckpoint it?
Not until someone has looked at it. A stair-step crack with blocks pushed out of line, or a wall that bows, means something is moving. That needs a structural look first, and tuckpointing comes after whatever is causing it is dealt with.
Show Us The Whole Wall
Take a step back and photograph the full elevation, then a few close shots of the sills, the block and any stone. That tells us which mortars the job needs and whether anything should get a structural look first. Call Guardian or send the photos through the contact page.