A Brick Front Is One Layer Thick. That Changes The Job.
Most brick in Buffalo Grove is a facing. On the colonials and split levels put up through the 1970s and 80s, builders laid a single layer of brick across the face of a wood-framed house, left a narrow air space behind it, and were supposed to leave small openings along the bottom course so water could get back out. Tuckpointing that brick takes the same cutting and packing as an old city wall, with a few rules of its own. And since whole streets went up in the same years, the fronts on a block tend to come due together.
What Sits Behind The Brick On These Houses
Take the brick off a Buffalo Grove colonial and the house would still be standing: wood studs, sheathing, and a water-resistant wrap over the sheathing. The brick sits just in front of all that, with a narrow air space between, held to the framing by thin metal ties. It carries its own weight and nothing more. Its job is weather. It keeps sun, wind and most of the rain off the house, and the space behind it deals with whatever rain gets through.
On a Chicago two-flat the brick is two or three layers deep and holds up the floors. At the joint itself the work is the same on both: worn mortar out, new mortar in, tooled to match. On veneer, what changes is everything around the joint.
Narrow Joints On A Thin Wall
Builders working a whole section at a time laid brick fast, with tight joints and a crisp tooled finish. Narrow joints get cut by the same rule as wide ones, roughly two to two and a half times their width, back to sound mortar. On a front only one brick deep there is nothing to gain past that. Cutting deeper weakens the face and drops grit into the space behind it.
Mortar droppings that fall in during a careless repair can pile up at the bottom and bridge across to the sheathing, which gives water a path into the house instead of down and out. Every joint we open on a veneer front is cleaned out toward the face and packed from the face, in lifts, so nothing goes through.
The Small Gaps Along The Bottom Row
Look along the lowest course of brick on your front, just above the foundation or the edge of the planting bed. On a properly built veneer wall there is a gap every few bricks: an open vertical joint, a small plastic tube, or a bit of rope wick. Those are weep holes. Water that gets past the brick runs down the back of it, lands on a flashing at the bottom, and drains out through them.
They are also the joints most often ruined by good intentions. A homeowner sees what looks like missing mortar and fills it, or a past repair packs the whole bottom row solid. Mulch topped up every spring creeps over them too. Any of those traps water behind the brick, where it soaks the bottom of the sheathing out of sight. Before we price a front we find the weeps, and they stay open through the job.
A veneer front was built to let a little water in, so the way back out has to stay open.
Built The Same Year, Worn The Same Way
Buffalo Grove went up a section at a time between the late 1960s and 1990, often with one builder working a whole street. The brick and mortar on a block went in the same way, and every front has stood through the same winters since. So fronts tend to wear in the same places at about the same pace. The side of the street that takes the weather head on usually goes first, along with the joints under window sills and the low courses beside the beds, where the brick stays damp.
When fronts up and down your street are getting work, yours is probably close behind. A veneer front that is due tends to show it across the face:
- Joints sunk back evenly from the brick edges, so each course throws a thin shadow line.
- Mortar that scratches out to sand with a key in more than one area.
- Hairline gaps opening between mortar and brick along long runs of horizontal joints.
- White salts showing in several places at once, a sign water is moving through the face.
- The joint under a window sill opened along its full length.
Where The Brick Meets The Siding
Plenty of colonials here carry brick across the first floor of the front with siding above it, and split levels often mix the two. Water running down the siding lands on the top course of brick. If the trim or flashing at that line has opened up, water gets behind the brick from the top and works down through the air space. We check that line, and the corners where the brick returns along the sides, before blaming the mortar. As the roofer on the job we look at the gutter above too, since a front that takes overflow wears out new joints as fast as old ones.
When The Front Needs More Than Mortar
Veneer stays on because of its ties. A front that bows outward, pulls away from a window frame, or shows a crack stepping through the brick with units out of line may mean ties have rusted through or something underneath has moved. That is a structural question, and it gets a structural look before anyone talks about joints. Caulk over a cracked joint, or mortar paint smeared across the face, hides the problem for a season and holds water in while it does.
For tuckpointing on older solid brick around Chicago, read our brick tuckpointing page. The gallery shows the crew’s roofing work, and a photo of your front can come in through the contact page.
Veneer Or Solid
A wood-framed house with brick on the face is veneer. Check the bottom row for small gaps every few bricks. Those are the weep holes.
Trips North From Alsip
Buffalo Grove work is grouped onto scheduled run days, and the drive never shows up on your bill.
One wide photo of the whole front, taken from the curb, is the best place to start.
(312) 590-4853How A Veneer Front Gets Done
Find The Weeps
Every weep hole along the bottom course is located and marked so it stays open.
Cut To The Width
Worn joints come out to about twice their width, back to sound mortar, and no deeper.
Clean Toward The Face
Dust and grit are cleared outward, so nothing drops into the air space behind the brick.
Tool To The Builder’s Line
New mortar goes in by lifts and is tooled at thumbprint-hard to the original profile.
If the worn mortar sits in one stripe under a gutter corner instead of across the face, tuckpointing repair is the smaller job. The day a full front gets redone, from covering the beds to the last brush, is laid out under brick repointing. A stack rising through the roof has its own page for chimney tuckpointing, and a porch or sunroom roof that dies into brick is covered on flat roof replacement. The Buffalo Grove page covers the village and its houses as a whole.
Before Anyone Cuts Into The Front
How do I know if my brick is veneer or a solid wall?
Most houses built here in the 1970s and 80s are wood framed, so the brick on the front is a single layer of veneer. Solid brick walls belong to much older buildings, like the two-flats and bungalows in Chicago.
What are the small gaps along the bottom row of brick?
Weep holes. Water that gets behind the brick drains down to a flashing and out through them. They need to stay open, so do not fill them with mortar or caulk, and keep the mulch below them.
Can tuckpointing push water into the wall behind the brick?
Done badly, it can. Cutting too deep, or letting grit and mortar fall into the air space, can bridge the gap to the sheathing and block the weeps. We cut to the right depth and clean and pack from the face, so the space behind stays clear.
Our front bows out a little near the top. Can tuckpointing fix that?
No. A bulge in veneer can mean the metal ties holding it to the house have failed, and new mortar in the joints will not pull it back. That gets a structural look first. Once the wall is sound, the joints can be tuckpointed.
Our mulch bed covers the bottom row of brick. Is that a problem?
It can be. Mulch piled over the weep holes holds water against the brick and closes the drainage path. Pull the bed down a few inches so the bottom course and its gaps are clear, and keep it there when you top it up each spring.
Our house is one of the newer ones north of Aptakisic. Does any of this apply?
Yes, since veneer is built the same way. Newer fronts are usually earlier in their life, and many still have sound joints. We still check the weep holes and the line where brick meets siding, and if the front is not due yet, we tell you that.
Let Us See The Whole Front From The Curb
Stand at the end of the driveway and take one photo of the entire front, then a close one of the worst joints and one of the bottom row of brick. That set usually tells us whether the front is due, whether it is one band or the whole face, and whether something above it needs fixing first.
You get a real number on the brick, listed apart from any roof or gutter work, and a run day on our next trip north. A supervisor is on site while the crew works, and the site is cleaned at the end of each day. The contact page works, and so does a phone call.