Alsip, IL · Mon–Sat 9–5 · BBB A+ Rated Emergency patch response: (312) 590-4853
Call Guardian Roofing (312) 590-4853
Skip to content
Drawing · Top courses fail first
Chimneys · Chicagoland

Chimney Tuckpointing From The Crew Already On Your Roof

A chimney is the tallest, most exposed piece of brick on the house, and it wears out from the top down. The last few courses under the crown take wind, driving rain and every freeze-thaw cycle with nothing above them for cover. Guardian Roofing Systems tuckpoints chimneys across Chicago and the suburbs, and because we are a roofing company, the flashing where the chimney meets the roof gets handled on the same trip instead of handed off to somebody else.

Why A Chimney Wears Out Before The Walls Below It

Walk around most Chicago bungalows and the side walls look fine while the chimney looks rough. That is not bad luck. A house wall gets some shelter from the eaves, the gutters and the house next door. A chimney stands up past the roofline in open air, wet on all four faces, warmed from inside when the furnace or fireplace runs and frozen from outside the same night. It is the hardest-working brick on the building and the brick people look at least, because nobody climbs up there until something leaks.

The Top Courses Take Every Storm

The mortar near the top of the stack fails first, and you can often see it from the sidewalk if you know what to look for: joints sunk back from the brick face, a few bricks that sit loose or out of line, and a lighter band where mortar has washed out. Water that gets into those top joints freezes, expands and pushes them open a little more each winter. Once the joints go, the bricks they held start to shift.

That is the case for catching it early. A chimney that only needed its top courses tuckpointed one year can need those courses taken down and relaid a few years later. Tuckpointing the top of a stack while the brick is still tight is a small job by chimney standards. Waiting until the crown is sitting on loose brick changes the conversation.

The Crown Is A Small Roof

The crown is the slab across the top of the chimney, around the flue. Its whole job is to shed water off the top and throw it clear of the brick faces below. A good crown slopes away from the flue and projects past the brick, so water drips off its edge instead of running down the wall. Plenty of older chimneys have a thin wash of mortar troweled over the top instead, flush with the brick, and those crack. Water then goes straight down into the core of the stack, which is where the top joints get their soaking.

A cap with a screen and a hood keeps rain, birds and leaves out of the flue. Some chimneys have one and many don’t. We look at the crown and the cap every time we tuckpoint a stack, because new joints under a cracked crown are fighting the same water that ruined the old ones.

Flashing Lives In The Mortar Joints

Where the chimney passes through the roof, two layers of metal keep water out. Step flashing is woven into the shingles and turned up against the brick. Counter-flashing comes down over it from above, and its top edge is bent into a mortar joint that was cut out to receive it, then mortared back in. That joint belongs to the roof and the masonry at once. When it fails, water runs behind the metal and down the inside of the chimney, and the stain shows up on a ceiling or beside the fireplace inside.

We find a lot of counter-flashing held on with a bead of caulk smeared over the joint, or metal screwed flat to the brick face. Both leak once the caulk dries out and pulls away. The real repair is cutting the joint clean, setting the metal back into it and packing that joint with mortar like every other joint on the stack.

Counter-flashing only stays put as long as the mortar joint holding it does.

One Crew For The Brick And The Roof Around It

Chimney leaks often involve two trades who blame each other. The mason tuckpoints the stack and leaves the flashing alone. The roofer replaces the flashing and never touches the brick. The leak survives both visits because the problem was the joint the flashing sat in. We are roofers who also tuckpoint, so one crew handles the whole intersection: the shingles at the base, the step flashing, the counter-flashing joints and the brick above them. Roof access gets set up once, the shingles below the stack get protected from falling mortar, and a supervisor is on the roof with the crew.

It helps with timing too. If the roof around the chimney is due for replacement soon, the best moment to tuckpoint the stack and reset the flashing is during the reroof, while the shingles are off. If the roof has good years left, we tuckpoint and reflash without disturbing more of it than the work requires.

What To Look For From The Yard And The Attic

You don’t need to climb anything to spot most of the warning signs. Check these from the yard, the attic or the room beside the chimney:

  • Joints near the top of the stack that look recessed, dark or missing, or bricks that sit out of line with the courses under them.
  • Chips of mortar or brick in the gutter, on the shingles below the chimney or on the ground.
  • White salt staining on the chimney faces, which means water is moving through the brick.
  • Rust streaks running down from the crown or from the flashing metal.
  • Water stains on the ceiling or wall next to the chimney, or damp framing around it in the attic.
  • A stack that looks like it leans when you view it from across the street.

The last one is a different kind of problem. A lean, or bricks that have clearly slid or bulged out of the stack, is a structural question. We tell you that plainly and get a structural look at it before anyone talks about tuckpointing, because new mortar packed into a stack that is moving does nothing about why it is moving.

On Every Chimney We Look At

Top-course joints, the crown and its overhang, the cap, step flashing, counter-flashing joints and the shingles around the base.

A leaning or bulged stack gets a structural look before any tuckpointing is discussed. Our gallery shows the crew’s roofing work.

(312) 590-4853

Chimney Work From The Top Down

Read The Stack

From the roof we check every face, the crown, the cap and the flashing, and photograph what we find so you see it too.

Cut From The Crown Down

Failed joints come out to sound mortar, starting at the top courses, with the shingles below covered against falling debris.

Reset The Counter-Flashing

Flashing joints are cut clean, the metal goes back into the joint, and that joint is packed like the rest of the stack.

Close Up The Crown

Crown cracks get addressed, the cap is checked, and the roof around the chimney is cleaned before we come down.

Chimney brick shares its problems with the rest of the house. If the joints on the walls below are also going, tuckpointing repair in the worst sections is usually the next conversation. Reading mortar joint failure covers cracks that may mean more than worn mortar, and older lime-mortar stacks fall under tuckpointing restoration. The shingles and step flashing at the base are shingle roof repair work, and a chimney rising through a low-slope roof ties into flat roof repair. We work on chimneys in Oak Lawn, Orland Park and Chicago.

Chimney Questions From Homeowners

Why is the mortar worst at the top of my chimney?

The top courses have the least protection on the house. They are wet on every side, they sit right under the crown where water collects if the crown is cracked, and they freeze and thaw more often than any wall below. That is why we start every chimney inspection at the top.

Do you fix the flashing and the brick at the same time?

Yes, and on a chimney that is usually the point. The counter-flashing sits in a mortar joint, so tuckpointing the stack and resetting the flashing are one repair. Splitting them between two trades on two visits is how a lot of chimney leaks outlive two repairs.

My chimney only leaks in hard, wind-driven rain. Is that the joints?

It can be. Wind pushes water into open joints on the weather side, and it also drives water up under loose counter-flashing. We check both, along with the crown. A photo of the stain inside and the chimney from outside helps us narrow it down.

Can a cracked chimney crown be repaired, or does it need replacing?

Small surface cracks in an otherwise sound crown can often be repaired. A thin mortar wash that is broken through, crumbling or flush with the brick usually needs to be replaced with a proper crown that sheds water past the faces. We tell you which one you have after we see it.

We never use the fireplace. Does the chimney still need tuckpointing?

If it still stands above the roof, yes. It takes the same weather as a working chimney, and its joints and flashing fail on the same schedule. Whether it vents anything has no effect on how the brick weathers.

Can’t the roofer just caulk around the chimney?

Caulk can slow a leak for a season, but it is not a repair. It pulls loose as the brick and metal move and as the sun dries it out. Caulk smeared over a counter-flashing joint also hides the joint we need to see, so we cut it out and reset the flashing properly.

HomeAdvisor Elite Service · Alsip, IL

Get A Look At The Top Of Your Stack

A photo of the chimney from the yard, plus one of any stain inside, tells us most of what we need before we come out. Call Guardian or use the contact page, and we will tell you what the chimney needs now and what can wait.

Protecting the roof that protects you.

The Company

Second-generation roofing and gutters out of Alsip, family-run since 2013. A supervisor on every roof, the site clean at the end of the day, and a straight answer before any work starts. Shingle, metal, flat, TPO, and commercial work across Chicagoland. BBB A+ rated, HomeAdvisor Elite Service award, licensed and insured in Illinois.

EST. 2013 · SECOND GENERATION

Reach Us

© 2026 Guardian Roofing Systems LLC. All rights reserved. BBB A+ · HomeAdvisor Elite Service · Licensed & insured in Illinois