Alsip, IL · Mon–Sat 9–5 · BBB A+ Rated Emergency patch response: (312) 590-4853
Call Guardian Roofing (312) 590-4853
Skip to content
Drawing · Each wall cut and matched
Street runs

Repointing The Whole Cul-De-Sac, One Wall At A Time

Whole streets in Carol Stream went up in the same season, so the brick on a cul-de-sac tends to need its joints at about the same time. When neighbors book together, one crew works the circle house by house on our scheduled DuPage run. Every wall is still cut, sampled and matched on its own, and every driveway is clean before the crew moves next door.

How A Street Gets Repointed Together

Repointing is the full job: worn mortar cut out of a wall, new mortar packed back in and tooled to match the joints around it. On a planned street the timing tends to line up, because the houses share a build year and the same builder’s brick and mortar. That makes a street a sensible thing to book as one run. It does not turn several walls into one wall, and the work is planned with that in mind from the first walk-around.

Who Signs Up, And When

Nobody has to commit for the whole circle. Each owner who wants the work gets a walk-around and a separate price, and the run covers the houses that say yes. A neighbor who would rather wait a year can wait. The point of booking together is practical: one crew, one setup on the street, and a shorter stretch of grinder noise on the block than the same houses done as separate jobs spread across a couple of summers.

The walk-around on each house is the same look a single job would get. Joints are scraped and tapped course by course, the gutter above the front is checked for spill, and step cracks or a brick face leaning away from the house get flagged for a structural look before anything is priced. Booking as a street changes the schedule. It never shortens that look.

Same Builder, Different Walls

The original mortar was most likely mixed the same way on every house in the phase. Decades later it rarely looks the same. A front facing south has bleached in the sun while the one across the circle, facing north, has stayed darker. On any given street one owner may have pressure washed the brick, and another may have had a corner patched in a gray mix that never matched anything.

So before any cutting, we mix a few sample batches for each house and let them cure on a board propped against that wall. The one that sits right with that brick in daylight is the one that goes in. A neighbor’s mix is a starting point at most.

Neighbors can share the crew and the week. Each wall still gets its own mix.

Cut Depth, House By House

Every wall gets cut to its own joints. The rule does not change, about two to two and a half times the joint width, usually 1/2 to 3/4 inch, back to sound mortar. What changes is how far a given wall has to go to reach it. A side wall that never takes the rain may be firm a half inch in, while a front under an overflowing five-inch builder gutter can be soft much deeper. Weep openings along the bottom course of a brick front stay open on every house we touch.

Inside The Temperature Window

Mortar needs temperatures holding above about 40 degrees F while it is placed and while it cures. On a single house that comes down to picking the days. On a street it comes down to sequence. We put the houses in an order that fits a stretch of workable weather, and we only open as much of any wall as the crew can pack and tool inside that window. No wall sits through a cold night with its joints cut open. If a cold snap arrives before a house is started, that house waits for the next workable stretch rather than getting rushed.

Cleanup Between Houses

The crew does not move to the next driveway until the last one is handed back. Between houses:

  • Tarps come down and get shaken out away from the next yard.
  • Driveways, walks and front steps are swept and rinsed of brick dust.
  • Planting beds are raked out and window sills wiped down.
  • Cut mortar is bagged and loaded on the truck instead of piling up at the curb.

We also watch the wind. Dust drifts on a tight circle, so the next house in line gets its windows covered before the grinder starts next door.

One Truck On The Circle

A cul-de-sac bulb gets tight with a work truck and a row of parked cars. Before the run starts we agree with the owners on where the truck and the mixing station sit, which driveways stay clear for people leaving for work, and the order that lets the crew move along the circle without blocking anyone in. Carol Stream is a scheduled run from our shop in Alsip with no travel fee, and once the crew is on the street it stays until the last house is done.

Guardian has been roofing out of Alsip since 2013 as a second-generation family company, licensed and insured in Illinois, with an A+ at the BBB and a HomeAdvisor Elite Service award. A supervisor is on every job, which counts for more when the job is a whole street. The general walkthrough of how we repoint any brick wall is on our brick repointing page.

Booking As A Street

Each house gets its own walk-around and its own price. The run covers whoever says yes.

Send the interested addresses and a photo of each front through the contact page.

When It Can Happen

Mortar wants temperatures holding above about 40 degrees F through the cure, so a street run lands in the warmer months.

The gallery shows the crew’s roofing work.

(312) 590-4853

A Run Down One Street

Walk Every House

Each front is read on its own, photographed and priced on its own.

Sample Each Wall

Trial mortar batches cure beside each wall until one sits right with that brick.

Cut And Pack

Joints come out to sound depth, are packed in layers and tooled to the profile already there.

Hand It Back

Driveway swept, beds raked, debris loaded, then the crew moves next door.

A street usually needs more than mortar. If the worn joints on your house sit in a strip under the gutter, start with tuckpointing repair under the eave, since the overflow has to stop first. Not sure whether your front is worn or just dirty? Brick tuckpointing on Carol Stream brick fronts walks through that test. Stacks that went up with the street are covered by chimney tuckpointing, the warehouses along Gary Avenue by flat roof replacement, and the Carol Stream page has the rest of what we do in town.

Booking A Street Together

Does every house on the street have to sign up?

No. Each owner who wants the work gets a separate walk-around and price, and the run covers the houses that say yes. Neighbors can join a later run. Booking together saves setup and weeks of noise on the street, and it never ties one house’s job to another’s.

Our houses went up the same year. Why not one mortar mix for all of them?

Because decades of weather have changed each wall differently. Sun, shade, an old pressure washing or a patch in a mismatched gray all shift how the joints look now. We cure sample batches beside each wall and use the mix that sits right with that brick.

What happens if a cold snap comes before you reach our house?

Your house waits for the next stretch of workable weather. Mortar needs temperatures holding above about 40 degrees F while it is placed and cures, and we only open as much wall as we can pack and tool inside that window. No joints sit cut open through a freeze.

Where does the truck sit while the crew works the circle?

We settle that with the owners before the run starts: where the truck and the mixing station go, which driveways stay clear in the morning, and the order of houses. The aim is that nobody on the street gets blocked in on a workday.

Is each house priced on its own?

Yes. Each front is walked, photographed and priced separately, and your number does not depend on whether the house next door signs. A wall with deeper wear costs more than one that is mostly sound, even on the same street. You see your own lines and nobody else’s.

How do we get our street onto the same run?

One neighbor can call, or send the interested addresses through the contact page. We set up the walk-arounds on our scheduled DuPage run, usually a day or two out, with no travel fee, and plan the order of houses from there.

Neighbors

Put The Whole Circle On One Run

Talk to the neighbors first. Then send the addresses that are interested, a photo of each front from the curb, and anything you already know about the walls, like a corner patched years ago or a gutter that spills onto the brick. If only one or two houses end up ready this year, the run still happens for them.

We set up the walk-arounds together, price each house on its own and build the run around the weather. Send the addresses through the contact page, or call the number below.

Protecting the roof that protects you.

The Company

Second-generation roofing and gutters out of Alsip, family-run since 2013. A supervisor on every roof, the site clean at the end of the day, and a straight answer before any work starts. Shingle, metal, flat, TPO, and commercial work across Chicagoland. BBB A+ rated, HomeAdvisor Elite Service award, licensed and insured in Illinois.

EST. 2013 · SECOND GENERATION

Reach Us

© 2026 Guardian Roofing Systems LLC. All rights reserved. BBB A+ · HomeAdvisor Elite Service · Licensed & insured in Illinois