Alsip, IL · Mon–Sat 9–5 · BBB A+ Rated Emergency patch response: (312) 590-4853
Call Guardian Roofing (312) 590-4853
Skip to content
Drawing · Worn joints left, repointed right
Joint by joint · Cook County

How We Repoint A Brick Wall, First Tarp To Last Brush

Brick repointing is mostly patience. Every joint gets cut to the right depth without nicking the brick, cleaned out, packed in layers and tooled at the moment the mortar is ready. Hurry any one of those steps and the wall tells on you within a couple of winters. This is how our crew runs a repointing job on a Chicago brick building, in the order it actually happens.

What Happens On The Wall, In Order

People picture repointing as a guy with a trowel. The trowel work is maybe a third of it. The rest is setup, cutting, cleaning and finishing, and those are the steps that separate a joint that lasts from one that falls out by the third spring. A supervisor is on site for every day of it, and the site gets cleaned up at the end of each day so you are not living in a work zone for a week.

Protecting The House Before Anything Gets Cut

Cutting mortar makes dust, a lot of it, and fine dust gets everywhere it is allowed to go. On a Chicago lot that includes your neighbor’s house, since two-flats and bungalows often sit a few feet apart across a gangway. Before the first cut we close things up:

  • Windows on the work elevation closed, then covered with plastic sheeting taped at the frame so dust cannot get pulled through the sash.
  • Air conditioning condensers and window units shut off and covered, since they will suck dust straight into the coils.
  • Shrubs, flower beds and the strip along the foundation covered with breathable tarps, with ground tarps laid to catch what falls.
  • Cars moved away from the wall or covered, and neighbors on a shared gangway given a heads-up about which days we are cutting.

Our grinders run with dust shrouds hooked to vacuums, and the crew wears respirators. Mortar dust carries silica, and nobody on the job or next door should be breathing it.

Grinder Or Hand Raking

A grinder with a diamond blade is fast, and on hard mortar in long bed joints it is the right tool. It also has two bad habits. It can cut wider than the joint, shaving the brick edges and leaving joints that look fat forever. And on the short vertical head joints it tends to overrun into the brick above and below.

So the grinder runs down the middle of the bed joints and stays shy of the edges, and the head joints get finished by hand with a plugging chisel. Old lime mortar that has gone soft often comes out with hand tools alone, which is gentler on soft common brick anyway. Which tool does how much of the work depends on how hard the old mortar is and how soft the brick is, and we decide that wall by wall.

Depth, And A Clean Back To Pack Against

Joints get cut out to roughly two to two and a half times their width, which on most Chicago brick lands around half an inch to three quarters of an inch, and always back to sound mortar. The back of the cut should be square. A V-shaped groove leaves a thin wedge of new mortar at the face with nothing behind it.

Then every joint gets cleaned. Air and a brush take out the dust and loose crumbs, and the joint is dampened before packing so dry brick does not pull the water out of the fresh mortar before it can set.

Mortar packed against dust is mortar that falls back out.

Packing In Lifts

Deep spots get filled first, in thin layers, each pressed in hard with a pointing trowel and left to firm up before the next goes on. Stuffing a deep joint full in one shot traps air and leaves a soft core that shrinks and cracks. Layering takes longer and it is the only way a deep joint ends up solid from back to face.

We also size each day’s section to what the crew can cut, pack and tool in one stretch of good weather. Cut joints do not sit open for days collecting rain and grit, and a section is worked from the top down, so the crumbs and drips land on brick that has not been pointed yet. When the forecast turns, the open joints get covered and the cutting stops until it clears.

Tooling To Match The Wall You Have

Before we start, we look at the undamaged joints on the building and match that profile, whether it is concave, V, flush, raked or struck. A new joint shaped differently from the old ones stands out more than a slight color difference does.

Timing matters as much as shape. The mortar gets tooled when it is thumbprint-hard, firm enough that a thumb leaves a print without sticking. Tooling at that moment compresses the surface and seals it against water. Too early smears the brick, and too late leaves a rough, open face.

Cleanup And The Brushed Finish

Once the joints have set up enough, a soft brush knocks off the crumbs and any light smear on the brick face. We stay away from harsh acid washes on soft old brick, because acid can burn the brick and the new mortar both. On a hot or windy day the finished wall gets misted so the mortar cures instead of drying out.

At the end we pull the plastic, vacuum the beds and the walks, and walk the wall with you.

Every Day On Site

A supervisor on the job. Windows, condensers and plantings covered before any cutting, and dust collection on every grinder.

The site cleaned at the end of each day, and a walk of the finished joints with you before we pack up. You can see how this crew leaves a job site in the gallery.

(312) 590-4853

The Order We Work In

Seal The Work Area

Plastic on the windows, covers on the condensers and beds, ground tarps down and the neighbors told which days are cutting days.

Grind Back To Firm Mortar

Grinder down the bed joints, hand chisel on the heads and near soft brick, every joint taken back to a square, solid back.

Pack And Tool

Joints dampened, filled in firm layers, then tooled at thumbprint-hard to the profile already on your wall.

Brush And Walk It

Crumbs brushed off, curing watched in bad weather, the site vacuumed, and the finished wall walked with you.

The mix that goes into those joints is its own decision, laid out on our repointing and mortar selection page. When a whole elevation needs it, full mortar joint replacement explains how the work is scheduled day to day, and tuckpointing for houses covers what a homeowner sees on the job. A chimney that needs the same work usually goes with chimney tuckpointing, and a wall soaked at one corner often points back to gutter repair. Crews run this process in Cicero, Oak Lawn and Orland Park.

Questions From The Day Of The Job

How much dust does brick repointing make?

A lot, if nobody controls it. Our grinders run with shrouds and vacuums, and windows, condensers and plantings are covered before the first cut. You will still see some dust on the ground tarps, which is what they are there for.

Do I need to be home while you work?

No. We need access to the walls and an outside water spigot, and it helps to know which windows open. Most people like to be around for the first morning and the final walk, and the supervisor is there either way.

Will the grinder damage my brick?

It can in careless hands, by widening joints and shaving the brick edges. We keep the blade in the middle of the bed joints and finish head joints and soft brick by hand. On very soft brick or soft old mortar, more of the job is done with hand tools.

How long does the new mortar take to cure?

It sets within a day but keeps curing for weeks. Keep the hose, the power washer and any sealer away from the new joints for the first month. Lime-rich mixes take longer than cement-heavy ones, so we will tell you which you have.

Why does the new mortar look different right after you finish?

Fresh mortar is darker while it is damp and dries lighter, and it is cleaner than joints that have weathered for decades. Give it a few months of weather before judging the color match. The profile should look right on day one.

Can you repoint around my windows and air conditioner?

Yes. Window frames are taped and covered, and joints right against frames and sills are cut by hand. Condensers and window units get shut off and covered while we cut, and turned back on when the dust is cleaned up.

Supervisor on every job · Alsip, IL

Put Your Wall On Our Schedule

Tell us which walls are bad and send a photo or two of the joints. We will come out, look at the brick and the old mortar, and give you a straight answer on scope and timing before any plastic goes up.

Protecting the roof that protects you.

The Company

Second-generation roofing and gutters out of Alsip, family-run since 2013. A supervisor on every roof, the site clean at the end of the day, and a straight answer before any work starts. Shingle, metal, flat, TPO, and commercial work across Chicagoland. BBB A+ rated, HomeAdvisor Elite Service award, licensed and insured in Illinois.

EST. 2013 · SECOND GENERATION

Reach Us

© 2026 Guardian Roofing Systems LLC. All rights reserved. BBB A+ · HomeAdvisor Elite Service · Licensed & insured in Illinois