Alsip, IL · Mon–Sat 9–5 · BBB A+ Rated Emergency patch response: (312) 590-4853
Call Guardian Roofing (312) 590-4853
Skip to content
Drawing · Interior wall, sheeted off
Inside brick · Chicagoland

Interior Tuckpointing Without Dusting Out The House

Exposed brick inside a home is a different job from a wall outside. Furniture, flooring, trim and the air you breathe are a few feet away, and the light in the room shows every mismatch. Guardian Roofing Systems tuckpoints interior brick in lofts, living rooms and basements across Chicago and the suburbs. We seal the room off, rake the joints by hand near anything finished, and match the mortar in the light you actually see it under.

Brick Inside The House Plays By Different Rules

Outside, a little dust on the lawn and a few days of scaffolding are part of the deal. Inside, the same work happens next to a couch, a hardwood floor and a return air vent that can carry fine dust to every bedroom. The mortar rules don’t change, but almost everything about how the work gets done does.

Where We Find Exposed Brick

In Chicago it shows up in a few predictable places. Converted warehouse and factory lofts with the original masonry walls left bare. Living rooms in older houses where someone pulled the plaster off a chimney breast or a party wall. Basements in bungalows and two-flats where the foundation brick was never covered at all. Each one has a different reason the joints are failing and gets a different plan.

A lot of that brick was never meant to be seen. It was laid as the back of a plastered wall, with rough joints, common brick and soft lime mortar. Stripping the plaster, and especially sandblasting it, can take the fired skin off the brick and leave a face that dusts when you brush it. That brick needs a soft mortar and a gentle hand, the same rules as old exterior brick, with more care at the edges.

Keeping Dust Out Of The Rest Of The House

Cutting mortar indoors makes fine dust that will find every room if you let it. Containment gets planned before a tool comes out:

  • Plastic sheeting taped floor to ceiling around the work area, with a zippered door so the crew can get in and out.
  • Heating and cooling vents in the room closed and covered, and the system shut off during cutting when it serves the rest of the house.
  • Floors covered with protection that won’t slide, and furniture moved out or wrapped.
  • A vacuum working right at the cut, and a full vacuum and wipe-down of the area at the end of each day.
  • Nearby doorways, outlets and built-ins masked off.

We go over the setup with you before the first day, including which rooms you won’t be able to use and when.

Hand Tools Near Finished Surfaces

Outside, a grinder clears most joints quickly. Inside, the edges of the wall sit against plaster returns, wood trim, window casings, flooring and sometimes cabinets, and a slipped blade there damages something that costs more to fix than the tuckpointing. Near those finishes we rake the joints by hand with chisels and raking tools. It takes longer. The trim stays intact. Out in the open field of a big loft wall we may cut with a grinder under dust control, then switch to hand tools as we get close to the edges.

The last day inside is mostly cleaning. Once the joints have set up enough to brush, we brush the wall down, take the plastic down slowly so the dust on it doesn’t drop back into the room, vacuum the floors and sills, and wipe down everything near the wall. The room should be ready to put back together when we leave, and the supervisor on the job walks it with you before the crew goes.

Matching Mortar Under Indoor Light

Daylight is forgiving outside. Indoors, a wall is lit from one window, a few warm bulbs and maybe a row of track lights aimed straight down it, and that raking light shows every difference in color and texture between new joints and old ones. So we mix samples, let them dry completely, and look at them on your wall, in your room, at the time of day you use the room. Dry mortar reads much lighter than wet, and fresh mortar has a crisper surface than century-old joints, so we brush the finished joints to soften that edge.

On an inside wall, the light in the room decides whether a new joint disappears or stands out.

White Powder On Basement Brick, Told Straight

The most common interior call is a basement wall with crumbling mortar, a white crust on the brick and a damp smell. That crust is efflorescence, salts left behind as water moves through the wall and dries on the inside face. It means water is coming through from outside. New mortar on the inside will look good for a while, but if water keeps pushing through, the salts and the damp come right back and the new joints soften the same way.

So we start with the water source. Downspouts that empty at the foundation, gutters that overflow above that wall, and soil or a walk that slopes toward the house are the usual causes, and as roofers we fix the gutter and downspout side ourselves. Sometimes the wall needs work from the outside or a waterproofing contractor, and we will tell you that rather than sell you an inside job that can’t hold. Cracks that step through the brick with displaced units, or a bowed basement wall, get a structural look before anything else.

A Fireplace Wall Still In Use

Plenty of interior jobs are the brick around a living room fireplace. The face and the chimney breast can be tuckpointed like any other interior brick. The firebox itself, the part that sees flame, is lined with firebrick laid in heat-rated mortar, and that is a job for a chimney specialist. We show you where our work stops before we start.

Inside Jobs We Plan For

Loft walls, living room chimney breasts, party walls with the plaster off, and basement foundation brick.

Room sealed off, vents covered, hand raking at every finished edge, and the area vacuumed down at the end of each day. Our finished roof jobs are in the gallery.

(312) 590-4853

How We Work Inside Your Home

Find The Water First

On basement walls and outside walls we look for what is wetting the brick before we talk about new mortar.

Match In Your Light

Samples dry on your wall in your room’s light, and you approve the color before any joint is packed.

Seal Off The Room

Plastic, a zippered door, covered vents and protected floors go up before the first joint is touched.

Rake By Hand At The Edges

Trim, plaster and flooring stay safe because the joints beside them are cleared with hand tools.

Interior brick follows the same mortar rules as outside walls. Choosing a mortar softer than the brick matters even more on stripped brick, and old lime-laid walls fall under tuckpointing restoration. The cutting and packing are laid out step by step in our brick repointing walkthrough, and the other face of the same wall is covered under exterior tuckpointing. Basement dampness often starts at the roof edge, which is gutter repair. We take interior brick jobs in Chicago, Oak Park and Oak Lawn.

Interior Brick Questions

How much dust does interior tuckpointing make?

A lot, if it isn’t contained. Cutting mortar produces a fine dust that travels through a house. We seal the work area with plastic and a zippered door, cover the vents, vacuum at the cut and clean the room at the end of every day, which keeps the rest of the house livable.

Can we stay in the house while you work on an inside wall?

In most cases, yes. You lose the room we are working in, and sometimes the path to it, while the job runs. We tell you before we start which rooms are affected, and anyone sensitive to dust may want to plan around the cutting days.

Our brick wall has old plaster stuck in the joints. Can you clean that out?

Yes. Plaster left in the joints after a wall was stripped is soft, and it usually comes out as we rake the joints for new mortar. Plaster smeared across the brick faces takes careful hand cleaning, so we test a small area first to see how the brick face takes it.

Why is there white powder on my basement brick?

That is efflorescence, salts left behind as water travels through the wall and dries on the inside. It means water is getting in from outside. Brushing it off or tuckpointing over it won’t stop it, so we look for the water source first, often a downspout, a gutter or the grade.

Will tuckpointing the inside of my basement wall stop a leak?

On its own, rarely. If water is coming through the wall, new mortar on the inside face is cosmetic and the damp returns. We find the source first and tell you honestly whether the fix belongs outside, at the gutters and downspouts, or with a waterproofing contractor.

Can you tuckpoint the brick around our fireplace?

The brick face and the chimney breast, yes, the same way as any interior wall. The firebox lining that sees the fire is firebrick in heat-rated mortar and is a job for a chimney specialist. We show you where our work ends before we start.

Family-run since 2013 · Alsip, IL

Show Us The Wall Inside

A photo of the wall, one close-up of the joints and a note on which room it is in gets us started. Call Guardian or reach us through the contact page, and we will tell you what the brick needs and how we will protect the room.

Protecting the roof that protects you.

The Company

Second-generation roofing and gutters out of Alsip, family-run since 2013. A supervisor on every roof, the site clean at the end of the day, and a straight answer before any work starts. Shingle, metal, flat, TPO, and commercial work across Chicagoland. BBB A+ rated, HomeAdvisor Elite Service award, licensed and insured in Illinois.

EST. 2013 · SECOND GENERATION

Reach Us

© 2026 Guardian Roofing Systems LLC. All rights reserved. BBB A+ · HomeAdvisor Elite Service · Licensed & insured in Illinois