Repair The Failed Joints, Then Stop The Water Behind Them
Brick walls rarely wear out evenly. They fail in patches, and the patches sit right where water lands: under a gutter that spills, beside a downspout that dumps at the wall, along a parapet top, below a window sill. Guardian Roofing Systems repairs those sections, finds the water that caused them, and blends the new joints into the old wall so the fix does not look like a fix.
Joints Give Out Where Water Lands
When someone calls about crumbling mortar, our first question is where. The answer nearly always lines up with a water problem somewhere above it. A wall that takes rain across its face and then dries out holds up for a long time. A wall that gets soaked in the same strip every storm, then freezes overnight, opens up fast. Freeze-thaw is what pries Chicago joints apart, and repeated wetting is what keeps feeding it.
Spot repair has a limit, though. If the failed joints are scattered across the whole wall instead of grouped under a water source, the wall is simply worn out, and patching it a few square feet at a time ends up costing more over a few years than doing the elevation once. We read the pattern of the damage before we recommend the size of the job.
Under An Overflowing Gutter
A clogged or sagging gutter turns a rainstorm into a curtain of water down one band of the wall. You can often read it from the sidewalk: darker brick, white salt bloom, and recessed joints running a few feet below the eave. Tuckpoint that band and leave the gutter alone and the joints start failing again on the same schedule. So we check the pitch, the hangers and what is sitting in the trough before we talk about the brick. Often the gutter repair is the smaller half of the job and the half that makes the other half last.
Where The Downspout Lets Go
Downspouts leak at the joints between sections and at the outlet. A loose elbow sprays the wall at head height. A downspout that ends at the foundation with no extension soaks the bottom courses and the grade-level masonry every time it rains, and those joints go sandy first. The repair comes in two parts: reconnect or extend the downspout so the water leaves the wall, then cut out and repack the damaged joints.
On corner lots and gangway walls, downspouts often empty onto a walk that slopes back toward the house, and splash-back alone can wet the first two feet of brick in every storm. We point out where the grade or a missing splash block is doing the damage, even when that part of the fix is something you can handle yourself.
Parapet Tops On Flat-Roof Buildings
Two-flats and three-flats with flat roofs often carry a brick parapet above the roofline. The top of that wall takes weather from both faces and from above, so its joints fail long before the wall below. Loose coping, open joints under the coping and failed roof flashing at the base of the parapet all feed one another. As roofers we are already up there, so the flashing and the parapet joints get looked at in the same visit. When the roof side needs work as well, that is flat roof repair.
If the water still hits the same spot, the new mortar is just the next thing to wash out.
Where Sills Shed Water
Limestone and brick sills are supposed to throw water off the front edge. When the drip edge is worn, or the sill has settled and tilts back toward the house, the water runs down the wall right under it. The joints at the sill ends and the first few courses below are the usual casualties. We check that the sill still pitches out, whether the joint between sill and brick is open, and whether water is getting in behind. Sometimes the sill joint is the real repair and the brick below is only the symptom.
Chimney Shoulders
On many bungalows the chimney runs up an outside wall and steps in at the shoulders, the sloped brick ledges where the stack narrows. Each shoulder is a small brick roof with nothing shedding water off it, so the joints there wear early. We repoint the shoulders, look at the wash on top, and check the chimney flashing while we are on the roof, because a leak at the flashing often shows up as damage much lower on the wall.
Shoulder joints are easy to miss from the ground. Mortar grit on the sill of the window beside the chimney, or chips of mortar on the walk below it, usually point straight up at the shoulders.
Making A Patch Disappear
A section repair has to sit inside a wall that has weathered for decades, and new mortar straight from the tub is brighter and smoother than the joints around it. To keep a patch from standing out, we match these:
- Sand color and grain, since weathered mortar shows far more sand at its surface than fresh mortar does.
- Mortar color, mixed and then checked against the existing joints once dry, because wet mortar always reads darker.
- Joint width, so the repaired joints do not look fatter than their neighbors.
- Tooled profile, whether the wall has concave, flush, raked or struck joints.
- Hardness, so the repaired section never ends up stronger than the brick around it.
We also feather the edge of every repair. Instead of stopping on a straight line, the cut-out section ends on a staggered edge that follows the brick bond, which hides the boundary. On a very old wall the color still settles over the next few seasons. And if a crack steps through the brick with units pushed out of line, or the wall bulges, that is a structural question first. We will say so and get it a structural look instead of filling it.
Spots That Fail First
Gutter lines, downspout outlets, parapet tops, sill ends, chimney shoulders and the courses at grade.
Send a photo through the contact page. The roofs we have finished are in the gallery, including gutters and parapets that sit right against brick.
(312) 590-4853How A Section Repair Runs
Trace The Water
We follow the stain up the wall to the gutter, downspout, sill or flashing that keeps putting water there.
Fix The Source
Gutters re-pitched, downspouts reconnected or extended, flashing reset. Skip this and the repair is temporary.
Cut Out The Section
Failed joints come out to sound mortar, about 1/2 to 3/4 inch deep, with the edges staggered along the bond.
Pack And Blend
Mortar goes in by lifts, gets tooled to the wall’s profile at thumbprint-hard, and is checked dry against the old joints.
If the patch turns into a bigger picture, brick tuckpointing for the whole house explains the full job. To sort a crack from ordinary crumbling, see how we read mortar joint failure. Exterior tuckpointing looks at the building envelope from coping to grade, and chimney brick gets its own page at chimney tuckpointing. Spot repair calls come in from Oak Lawn, Orland Park and Tinley Park all season.
Questions About Spot Repairs
Can you repair just one section of a brick wall?
Yes, and on most houses that is the right call. Joints fail in the wettest spots first, so we cut out and repack the failed section and leave sound mortar alone. If the rest of the wall is close behind, we will tell you.
Will the repair stand out from the rest of the wall?
Fresh mortar always looks a little cleaner at first. We match sand, color, joint width and profile, and stagger the edges of the repair along the brick pattern so there is no straight seam. Most patches settle in after a season of weather.
Why do you want to fix my gutter before the mortar?
Because the gutter is usually why the mortar failed. Water spilling down the same strip of wall every storm, then freezing, opens joints fast. Repoint without fixing it and the new joints start the same cycle.
The mortar under my window sill keeps crumbling. Why there?
Water running off the sill is ending up on the wall instead of dripping clear. A sill that tilts back, a worn drip edge or an open joint between the sill and the brick will all do it. We check the sill first, then repair the joints below.
Can I caulk the open joints for now?
Caulk over mortar joints traps water in the wall and makes the real repair harder, because every bit of it has to be cut back out. Smear-over mortar coatings cause the same trouble. If you need to buy time, fix the gutter or downspout first, which slows the damage more than any sealant will.
When does a crack mean something bigger than tuckpointing?
A stair-step crack where bricks have shifted out of line, a wall that bulges, or a crack that keeps widening is a structural question. That gets a structural look before anyone tuckpoints it. Filling it first only hides the evidence.
Send A Photo Of The Bad Spot
Step back far enough to get the gutter or sill above the damage into the frame. That one picture usually tells us if you are looking at a small repair, a water problem, or both. Reach us through the contact page or call Guardian directly.