Alsip, IL · Mon–Sat 9–5 · BBB A+ Rated Emergency patch response: (312) 590-4853
Call Guardian Roofing (312) 590-4853
Skip to content
Drawing · Worn joints left, repointed right
Brick · Chicagoland

What Tuckpointing Really Means On A Chicago Brick House

On a Chicago brick house, tuckpointing means cutting the worn mortar out of the joints and packing new mortar back in, by hand, a layer at a time, to a finish that matches the wall. Guardian Roofing Systems does this work on bungalows, two-flats and the brick garages behind them across Chicago and the suburbs. We start with the wall, tell you which joints need it and which ones don’t, and give you a straight answer before anything gets cut.

Where The Word Came From And What It Means Now

Ask anyone on a Chicago block what tuckpointing is and you will hear about the crew with the grinder and the dust tarps, working their way down the gangway side of a bungalow. That is the job most people mean, and it is the job this page covers. The word itself is older than the grinder, though, and it used to mean something narrower.

The Original Tuck Was A Thin Line

Tuckpointing started as a finishing trick. Builders filled the joints with mortar tinted close to the brick color, then ran a narrow raised strip of light lime putty down the center of each joint. That strip was the tuck. From across the street it made ordinary brick with wide, uneven joints look like fine brickwork laid with razor-thin ones. It was decorative, slow and fussy, and you can still find traces of it on a few older facades if you know to look.

How Chicago Uses The Word Today

Here the meaning stretched. In everyday Chicago talk, tuckpointing now covers any job where failed mortar comes out of the joints and new mortar goes back in. Some masons call that repointing, and they are right, but if you call us asking for tuckpointing we know exactly what you mean. Nobody expects a raised white line. What matters is the work underneath the name: how deep the old mortar comes out, what goes back in, and how the joint is finished.

Common Brick On Bungalows And Two-Flats

A lot of what we look at is Chicago common brick, the softer, often salmon to buff colored brick on the sides and backs of bungalows and on plenty of two-flats, with a harder face brick dressing the street side. Common brick soaks up water and gives it back. The mortar between those bricks should be softer still, because the joint is the part of the wall that is meant to wear out first. A joint can be cut out and refilled. A brick face that has popped off cannot be put back.

Mortar is the part of a brick wall you are supposed to replace, so it should always be the weakest thing in the wall.

That is why the mix matters as much as the labor. Hard, cement-heavy mortar packed around soft brick forces the water and the movement into the brick, and the faces start to spall. We match the mortar to the brick in front of us, and we tell you when a wall needs that extra care.

One Wall, Start To Finish

Here is what tuckpointing one brick elevation involves when it is done right:

  • Walk the wall and mark the joints that are sandy, recessed, cracked or missing, plus the ones that are still sound and stay put.
  • Protect windows, sills, plantings and the walk below before any cutting starts.
  • Cut the old mortar out to about two to two and a half times the joint width, usually 1/2 to 3/4 inch, until we reach sound mortar.
  • Clear the dust out of every cut joint and dampen it so the brick does not pull water out of the new mortar.
  • Pack new mortar in lifts, one layer firmed before the next, instead of one thick fill that shrinks and cracks.
  • Tool each joint when the mortar is thumbprint-hard, to the profile the wall already has: concave, V, flush, raked or struck.
  • Brush the wall down and clean up the site before we leave for the day.

Skipping a step shows up later. Shallow cutting is the most common shortcut, and a thin skim of new mortar over half an inch of old, crumbling material falls out after a couple of winters.

On a typical bungalow we set up on one elevation at a time, so the house is never wrapped in tarps all at once. The gangway walls are usually the tight spots, with the house next door a few feet away and its windows right in the line of the dust. We go over access with you before the first day, and if a neighbor needs a heads-up, we tell you early enough to give one.

Why A Roofing Company Does This Work

We are roofers first, and roofers work brick every week. Every chimney, parapet wall and wall flashing we touch ties into the masonry, and counter-flashing gets set into a mortar joint we cut ourselves. Gutters and downspouts decide where water hits a wall, which is usually where the worst joints are. So when we look at your brick we are also looking at what sits above it. Tuckpointing under an overflowing gutter fails again unless the gutter gets fixed too.

Timing The Job

Mortar needs temperatures holding above roughly 40 degrees while it sets and cures, so most Chicago tuckpointing runs from spring into late fall. Winter work is possible with an enclosure and heat, or the wall waits. We also watch for step cracks with displaced brick, or a section that bulges. Those are a structural question, and they get a structural look before anyone tuckpoints over them. Send a few photos through the contact page and we will tell you which kind of problem you have.

Drawing · Cut out, repacked, original

What We Check First

Joint depth, mortar hardness under a nail, step cracks, spalled faces, and where the gutters and downspouts drop their water.

The gallery is our roof work for now, the same crew and the same standards. A supervisor is on every job, and the site gets cleaned at the end of each day.

(312) 590-4853

The Brick Tuckpointing Sequence

Mark The Joints

We scratch, tap and sight along the wall, then mark which joints come out. Sound mortar stays where it is.

Cut To Sound Mortar

Joints are cut to roughly twice their width or a little more, square at the back, so new mortar has something to grip.

Pack In Layers

New mortar goes in a lift at a time, each one firmed before the next, with the mix chosen for your brick.

Tool To Match

At thumbprint-hard we tool every joint to the wall’s existing profile, then brush the face clean.

Other brick work on this site: when only one section of a wall has failed, tuckpointing repair at the problem spot is the smaller job. Buildings from before 1930 with lime mortar belong under tuckpointing restoration for older brick. If a whole elevation is coming out, see how full mortar joint replacement runs day to day, and our brick repointing walkthrough covers the cutting and cleanup in detail. Chimney brick has its own page at chimney tuckpointing. We work on brick houses in Chicago, Berwyn and Cicero.

Questions About Brick Tuckpointing

What is the difference between tuckpointing and repointing?

In Chicago the two words mostly mean the same job: cutting out failed mortar and replacing it. Strictly speaking, tuckpointing first meant adding a thin decorative line of contrasting mortar along each joint. Call it either one and you get the same work from us.

How can I tell if my brick house needs tuckpointing?

Look for joints that have sunk back from the brick face, mortar that turns to sand when you rub it, and gaps you can see a shadow in. White salt stains on the brick mean water is moving through the wall. A photo of the worst area usually tells us a lot.

Do you have to tuckpoint the whole house at once?

No. Most bungalows and two-flats wear unevenly, with the weather side and the strips under the gutters going first. We mark what needs work and leave sound joints alone, and we will tell you if the whole wall really is due.

Will the new mortar match my old mortar?

We match the color, sand and joint profile to your wall, and new mortar looks a little fresher until it weathers. On a street-facing wall we do a small sample area first so you can see the color dry. Brushing the finished joints helps them sit into the old wall.

Can you tuckpoint in the winter?

Mortar needs temperatures holding above about 40 degrees while it sets and cures. In winter that means enclosing and heating the work area, or waiting for spring. Most homeowners choose to wait unless water is getting inside.

Is brick dust going to get everywhere?

Cutting mortar makes dust, and there is no avoiding it. We cover windows, plants and anything close to the wall, keep the work area as contained as we can, and clean the site at the end of each day. Tell us about cars, gardens or a neighbor’s windows near the wall and we plan around them.

BBB A+ · Alsip, IL

Start With A Look At The Wall

Tell us the street, roughly when the house was built if you know, and send a photo of the worst wall. We will tell you how much of it needs tuckpointing and what it will take. Call Guardian or reach us through the contact page.

Protecting the roof that protects you.

The Company

Second-generation roofing and gutters out of Alsip, family-run since 2013. A supervisor on every roof, the site clean at the end of the day, and a straight answer before any work starts. Shingle, metal, flat, TPO, and commercial work across Chicagoland. BBB A+ rated, HomeAdvisor Elite Service award, licensed and insured in Illinois.

EST. 2013 · SECOND GENERATION

Reach Us

© 2026 Guardian Roofing Systems LLC. All rights reserved. BBB A+ · HomeAdvisor Elite Service · Licensed & insured in Illinois